OEM TOYOTA 2005-2017 Key Fob Remote Keyless Entry Alarm Car Control GQ43VT20T

Why purchase a recycled keyless entry remote transmitter?

The

vehicle keyless remote key fob you are going to purchase from us is pre-owned;

aka: used, previously loved ;). We recycle OEM and aftermarket keyfobs and put

them through a concise refurbishing process so we can guarantee our products

are delivered to you in a ready-to-program state. We offer these car clickers

at a significant cost savings to stealerships so you can keep your hard earned

cash for something more fun while lightening your ecological footprint J . We call

that a win-win! Why wait? Add some convenience to your daily routine and help

save the environment, order your recycled car remote control today!

What are you purchasing?

This is ONE (1) Factory

OEM (Original Equipment Manufacturer) keyless entry remote, aka "key

fob" that will work with your OEM Factory installed RKE system .

Compatibility: Works

with vehicles that use a factory keyless entry system listed in our

compatibility section above AND below.

FCC ID#(s)

GQ43VT20T

Alternate Spellings

GQ4-3VT20T, GQ4 3VT20T, GQ43VT20T,

GQ43VT2OT, GO43VT20T, G043VT20T

Part #(s)

IC

#: 14701-1T

Dealer #(s)

89742-AE010

Button Count

3;

Lock, Unlock, Panic

Battery (installed)

1;

CR2032

Frequency

315

MHz (MHz)

Programming:

Please note not all customers will be able

to complete the programming on their own so if you are having trouble or

unsure diagnostic programming is available at your local qualified automotive

locksmith or car/audio shop.

Programming Instructions: 2008 2009 2010 2011 2012 Toyota Sequoia * 2004 2005 2006 2007 2008 2009 2010 2011 2012 Toyota Sienna * 2005 2006 2007 2008 2009 2010 2011 2012 Toyota Tacoma * 1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked. 2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out. 3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out. 4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition. 5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. 6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons,Press the

lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock

and then unlock once indicating successful programming. If the door locks cycle twice,

repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote. 7. Open drivers door.

Programming Instructions: 2007 2008 2009 2010 2011 2012 Toyota Highlander Base *** 2004 2005 2006 2007 2008 2009 2010 2011 2012 Toyota Tundra *** METHOD #1: 1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked. 2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out. 3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out. 4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition. 5. Within 3 seconds, the power door locks should lock then unlock automatically

indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. 6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and

hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating

successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote

was not accepted. C. Repeat steps A and B in step 6 for each new remote 7. Open drivers door. METHOD #2: If the above programming method (#1) does not work to sync the remote THEN diagnostic programming required. What you will need: 1. Your vehicle 2. The keyless entry remote control A locksmith is least expensive: autolocksmithfinderus.com or global-locksmith.com As a last resort: you can visit your local car dealer for diagnostic programming. The procedure takes a few seconds to complete so many dealers will do it as a courtesy, but please verify this before purchasing. Some dealers charge for one hour labor to sync your remote with your RKE system. If your dealer does charge a fee, local locksmiths usually charge much less.

Condition Notes

Pre-owned ready to program to your compatible vehicle RKE system.

Installed RKE System Type :

Please be sure you have a FACTORY (RKE) remote keyless entry system .

It was not standard on all vehicles. If your current remote looks the same then

this will work. Other options include: Dealer Installed or Aftermarket. The

system installed in your vehicle will CHANGE the required remote. If you are

unsure ask your local dealer they will need your VIN # (Vehicle Identification

Number (located on our vehicle registration car, on your driver side door jam,

or your windshield (lower left drives side))).

Why does your vehicles installed RKE / Security system

determine which remote control your can purchase?

The remotes job is to pair with your vehicles

installed RKE system. It will only sync to a matching system; therefore, you

cannot purchase a different type of remote than the remote manufactured with

the system. It will not pair with a foreign system.

Programming :

We will send you information on how to locate

programming requirement/instructions for your make, model, and year vehicle.

Some vehicles have DIY (do-it-yourself) programming instructions available.

While other vehicles require diagnostic programming which is available at your

local qualified automotive locksmith or dealer.

Programming Requirement Information NOTE :

The

vehicle manufacturers determine the programming requirements at the time of

manufacture. We pass the programming requirements / instructions on to you as a

courtesy. We do not write the programming nor do we determine which vehicles

require diagnostic programming and which vehicles can be programmed by the you

(DIY). We are not locksmiths nor mechanics nor are we familiar with EVERY

vehicles program sequence. If you have questions:

1.

Check your Vehicle Owners Manual for OEM Factory remotes or The User Manual for

Dealer Installed or Aftermarket RKE systems.

2.

YouTube has many video postings from do-it-yourselfers to assist with all kinds

of questions & most customers find if very helpful to WATCH the programming

being done which can eliminate mistakes in the sequence.

To

locate the programming for your vehicle via this method go to YouTube and once

there in the search bar type in the following:

i.

If

you have a factory RKE system: your make model year + the words program remote

(i.e.: 2005 Ford Mustang program remote)

ii.

If

you have a dealer installed or aftermarket RKE system: the FCC ID or system

type + the words program remote (i.e.: ELVAT5C program remote or AS200 program

transmitter?)

3. For OEM FACTORY

installed systems: send us an eBay message with your vehicles make, model &

year = we can pass on to you any programming information requirements we have

on hand.

4. For

DEALER INSTALLED RKE installed systems: send us an eBay message with your

remote controls FCC ID # and PART# and the vehicles make, model, & year =

we can pass on to you any programming information requirements we have on hand

(the programming for dealer installed RKE systems will be different than

Factory or Aftermarket installed RKE systems).

5. For AFTERMARKET

INSTALLED RKE installed systems: send us an eBay message with your remote

controls FCC ID # and PART# = we can pass on to you any programming information

requirements we have on hand (the programming for aftermarket installed RKE

systems will be different than Factory or Dealer installed RKE systems).

6.

There are also many auto forums that you can go onto by just conducting a

google search with your questions.

7. or a local automotive

locksmith or your local parts/car/audio store will typically be able to assist

you if you are trying to avoid the dealer.

Normal

0

false

false

false

EN-US

X-NONE

X-NONE

•

•

•

Powered by Frooition

• About us

• Shipping

• Returns

• Payment

• FAQs

All Items

See our eBay store for more great items >>

Shop Categories

Other

89742-AE010 07 08 09 keyless remote entry transmitter beeper fob clicker alarm

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Item Description